ICC Bolting Exam 2022 with complete solution

ICC Bolting Exam 2022 with complete solution According to the IBC, the "blank" is to hire the special inspector. -Answer- owner or owners agent. 2009 IBC Section 1704.1 According to the IBC, the "blank" is the resp ...

ICC Bolting Exam 2022 with complete solution According to the IBC, the "blank" is to hire the special inspector. -Answer- owner or owners agent. 2009 IBC Section 1704.1 According to the IBC, the "blank" is the responsible for the approval of a person's qualifications to act as a special inspector. -Answer- code official. 2009 IBC, Section 1704.1 According to the IBC, discrepancy corrections are made known to the building official by: -Answer- final report. 2009 IBC, Section1704.1.2 When is the code official to be made aware of a discrepancy found during a special inspection? -Answer- If it is not corrected by the contractor. 2009 IBC, Section 1704.1.2 According to the Model Program for Special Inspection, the special inspector is to document work that is nonconforming: -Answer- In a written report - Section II B 4 - Model Programs According to the Model Program for Special Inspection, the special inspector is to prepare written report of inspection: -Answer- After each inspection visit - Section II B 5 - Model Programs According to the Model Program for Special Inspection, which of the following items does not need to be included in each inspection report? -Answer- Description of discussions with the contractor - Section B 5 - Model Programs According to the Specification for Structural Joints using high strength bolts, the nominal diameter of standard bolt holes shall be how much larger than the nominal bolt diameter? -Answer- 1/16 inch - Specification for Structural Joints Table 3.1 Discrepancies in the work shall be brought to the immediate attention of the "blank" for corrective action. -Answer- the contractor - 2009 IBC, Section 1704.1.2. The special inspector shall furnish inspection reports to the "blank" and to the "blank"? -Answer- Building Official and Registered Design professional The special inspector shall provide continuos inspection of: -Answer- Single-pass fillet welds greater than 5/16 inch in size - 2099 IBC, Table 1704.3, Item 5.3 The special inspections required by this code are not required where the work is done on the premise of a? -Answer- Approved fabricator - 2009 IBC, Section 1704.2.2 The special inspection of the steel fabrication process shall not be required where the fabricator does not perform any? -Answer- heating operations - 2009 IBC, Section 1704.3, Exceptions # 1 According to the Specifications for Structural Steel Buildings, ASTM Standard "blank" is to be used for the material test for steel sheets. -Answer- A568 - Section A31, Specifications for Structural Steel Buildings According to the Specifications for Structural Steel Buildings, the "blank" conducts the material tests for identification of the structural steel. -Answer- Fabricator or Testing Laboratory - Section A31, Specifications for Structural Steel Buildings. According to the Specifications for Structural Steel Buildings, which of the following steel members are allowed to be unidentified steel? -Answer- Unimportant members, where their physical properties and weldability would not affect the structure strength - Section A31b, Specifications for Structural Steel Buildings According to the Code of Standard Practice for Steel Buildings and Bridges, how is steel of special material to be identified? -Answer- It is marked by the supplier - Section 5.1.1, Code of Standard Practice for Steel Buildings and Bridges According to the Code of Standard Practice for Steel Buildings and Bridges, how are fabricators stock steel material identified? -Answer- Certified mill test reports - Section 5.2.2 - Code of Standard Practice for Steel Buildings and Bridges According to the Specification for Structural Steel Buildings, what ASTM Standard would apply to a sample for structural steel pipe? -Answer- A53 - Section A31a - Specification for Structural Steel Buildings According to the Code of Standard Practice for Steel Buildings and Bridges, the number of samples required to be tested for structural steel is: -Answer- The number specified by the ASTM specification - Section 5.1.1 - Code of Standard Practice for Steel Buildings and Bridges According to the Specification for Structural Steel Buildings, which ASTM standard would apply to a sample for structural steel plates? -Answer- A36, A283, and A242 - Section A31a - Specification for Structural Steel Buildings According to the Specification for Structural Steel Buildings, "blank" tests are required for samples for built-up sections consisting of plates over 2 inches in thickness. -Answer- Charpy V-notch testing - Section A31d, Specification for Structural Steel Buildings According to the Specification for Structural Steel Buildings, ASTM standard "blank" would apply to a sample for structural steel bars. -Answer- A36, A529, and A572 - Specification for Structural Steel Buildings Steel furnished for structural load-carrying purposes shall be properly : -Answer- Identified - 2009 IBC, Section 2203.1 Steel that is not readily identifiable as to grade by marking and test records shall be: -Answer- tested - 2009 IBC, Section 2203.1 Where materials or assemblies are required by this code to be labeled, such material and assemblies shall be labeled by: -Answer- An approved agency - 2009 IBC, Section 1703.5 Inspection of the steel frame for compliance with the approved construction documents should verify: -Answer- Member location, Bracing, and Stiffening - 2009 IBC, Section 1704.3.2. Continuous inspection of bolt pre-tensioning is required when using: -Answer- The calibrated wrench method - 2009 IBC, Section 1704.3.3.3. Where required by the code, the building owner shall employ a registered design professional to perform: -Answer- Structural Observation - 2009 IBC, Section 1709.1 According to the Specification for Structural Joints, how does the special inspector verify the bolts, nuts, and washers meet the requirements of A325 or A490 specifications? -Answer- Manufacturer certification - Section 2.1 - Specification for Structural Joints According to the Specification for Structural Joints, how are the high-strength bolts, nuts, and washers to be stored at the job site? -Answer- In a protected shelter in closed containers - Section 2.2 - Specification for Structural Joints According to the Specification for Structural Joints, how does the special inspector determine the type of high-strength bolts that are to be used for a project or particular bolt joints? -Answer- The engineer of record's project drawings - Secton 2.3.1 - Specification for Structural Joints According to the Specification for Structural Joints, what is the minimum high-strength bolt extension from the outer face of the nut after installation? -Answer- flush - Section 2.3.2 - Specification for Structural Joints According to the Specification for Structural Joints, for snug tightened joints, washers are required only for which of the following conditions? -Answer- When a slotted hole occurs in the outer ply of the joint and/or when the outer face of a joint has a slope greater than 1:20 - Section 6.1 - Specification for Structural Joints According to the Specification for Structural Joints, for pretensioned and slip critical joints, which of the following conditions require washers in the high-strength bolted connection? -Answer- Calibrated wrench pretensioning, Oversized or slotted hole in the outer ply of the connection, or Twist-off type tension control bolt. - Section 6.2 - Specification for Structural Joints.