CEng 487 - SOIL MECHANICS II
Lecture Notes
Chapter 1: Shear Strength of Soils.
Chapter 2: Bearing Capacity of Shallow Foundations.
Chapter 3: Lateral Earth Pressure.
Chapter 4: Slope Stability.
References:
1. Tefe
...
CEng 487 - SOIL MECHANICS II
Lecture Notes
Chapter 1: Shear Strength of Soils.
Chapter 2: Bearing Capacity of Shallow Foundations.
Chapter 3: Lateral Earth Pressure.
Chapter 4: Slope Stability.
References:
1. Teferra, A. & Mesfin, L., 1999. Soil Mechanics, AAU
2. Budhu M., 2000. Soil Mechanics and Foundations, Wiley and Sons.
3. Cernica, J. N., 1995. Geotechnical Engineering - Soil Mechanics, Wiley and sons.
4. Prakash, S., 1995. Fundamentals of Soil Mechanics, Prakash Foundation.
5. Das, B. M., 1995. Principles of Foundation Engineering, PWS pub. Co.
6. Bowles, J. E., 1996. Foundation Analysis and Design, Joseph E. Bowles, McGraw-Hill.
Addis Ababa University, Faculty of Technology, Department of Civil Engineering
Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 1
CHAPTER ONE
SHEAR STRENGTH OF SOILS
1.0 Introduction
The safety of any geotechnical structure is dependent on the strength of the soil. If
the soil fails, a structure founded on it can collapse, endangering lives and causing
economic damages. Soils fail either in tension or in shear. However, in the majority of soil
mechanics problems (such as bearing capacity, lateral pressure against retaining walls,
slope stability, etc.), only failure in shear requires consideration. The shear strength of
soils is, therefore, of paramount importance to geotechnical engineers. The shear
strength along any plane is mobilized by cohesion and frictional resistance to sliding
between soil particles. The cohesion c and angle of friction φ of a soil are collectively
known as shear strength parameters.
In this chapter we will define, describe, and determine the shear strength of soils.
When you complete this chapter, you should be able to:
! Determine the shear strength of soils.
! Understand the difference between drained and undrained shear strength.
! Determine the type of shear test that best simulates field conditions.
! Interpret laboratory and field test results to obtain shear strength
parameters.
Sample Practical Situation: You are the geotechnical engineer in charge of a soil
exploration program for a dam and a housing project. You are expected to specify
laboratory and field tests to determine the shear strength of the soil and to recommend
soil strength parameters for the design of the dam.
1.1 Definitions of Key Terms
Shear strength of a soil (τ ) is the maximum internal resistance to applied shearing
stresses.
Angle of internal friction (φ ) is the friction angle between soil particles.
Cohesion (c) is a measure of the forces that cement soil particles.
Undrained shear strength of a soil (Su) is the shear strength of a soil when sheared at
constant volume.
Addis Ababa University, Faculty of Technology, Department of Civil Engineering
Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 2
1.2 Coulomb’s Frictional Law
You may recall Coulomb’s frictional law from your courses in statics and physics. If
a block of weight W is pushed horizontally on a plane (Fig. 1.1a), the horizontal force (H)
required to initiating movement is:
H = µW (1.1)
Where µ is the coefficient of static friction between the block and the horizontal plane.
The coefficient of friction µ is independent of the area of contact. It is, however,
strongly dependent on the nature of the surface in contact – the type of material, the
condition of the surface, and so on. Furthermore, in most materials the coefficient of
static friction is larger than the kinetic coefficient. The angle between the resultant force
R and the normal force N (Fig. 1.1) is called the friction angle, φ µ1 tan − = .
Figure 1.1: (a) Slip plane of a block. (b) A slip plane in a soil mass.
In terms of stresses, Coulomb’s law is expressed as:
τ f = σ n tanφ (1.2)
where τ f (= T/A, where T is the shear force at impending slip and A is the area of the
plane parallel to T) is the shear stress when slip is initiated, and σ n (= N/A) is the normal
stress on the plane on which slip is initiated. Coulomb’s law requires the existence or the
development of a critical sliding plane, also called slip plane or failure plane. In the case
of the block the slip plane is at the interface between the block and the horizontal plane.
1.3 Mohr’s Circle for Stress
The stress states at a point within a soil mass can be represented graphically by a
very useful and widely used devise known as Mohr’s circle for stress. The stress state at
a point is the set of stress vectors corresponding to all planes passing through that point.
For simplicity, we will consider a two-dimensional element with stresses as shown in Fig.
Addis Ababa University, Faculty of Technology, Department of Civil Engineering
Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 3
1.2a. Let’s draw Mohr’s circle. First, we have to choose a sign convention. In soil
mechanics, compressive stresses and clockwise shear are generally assumed to be
positive. We will also assume thatσ z > σ x .
Figure 1.2: Stresses on a two-dimensional element and Mohr’s circle.
The two coordinates of the circle are (σ z τ zx , ) and (σ x −τ zx , ). Recall from your
strength of materials course that, for equilibriumτ xz = −τ zx . Plot these two coordinates
on a graph of shear stress (ordinate) and normal stress (abscissa) as shown by A and B
in Fig. 1.2b. Draw a circle with AB as the diameter. The circle crosses the normal stress
axis at 1 and 3, where shear stresses are equal to zero. The stresses at these points are
the major principal stress,σ 1 , and the minor principal stress, σ 3 .
The principal stresses are related to the stresses σ x σ z , and τ zx by the following
relations:
2
2
1 2 2 zx
z x z x τ
σ σ σ σ
σ +
− +
+ = (1.3)
2
2
3
2 2 zx
z x z x τ
σ σ σ σ
σ +
− − + = (1.4)
The angle between the major principal stress plane and the horizontal plane (ψ ) is:
x
zx
σ σ
τ
ψ − =
1
tan (1.5)
The stresses on a plane oriented at an angle θ to the major principal stress plane are:
θ σ σ σ σ
σ θ cos 2
2 2
1 3 1 − 3 +
+ = (1.6)
Addis Ababa University, Faculty of Technology, Department of Civil Engineering
Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 4
θ σ σ
τ θ sin 2
2
1 − 3 = (1.7)
In the above equations θ is positive for clockwise orientation. The maximum shear
stress is at the top of the circle with magnitude:
2
1 3
max
σ σ
τ − = (1.8)
The stress σ z acts on the horizontal plane and the stress σ x acts on the vertical
plane. If we draw these planes in Mohr’s circle, they intersect at a point, P. Point P is
called the pole of the Mohr circle. It is a special point because any line passing through
the pole will intersect Mohr’s circle at a point that represents the stresses on a plane
parallel to the line. Let us see how this works. Suppose we want to find the stresses on
a plane inclined at angle θ to the horizontal plane as depicted by MN in Fig. 1.2a. Once
we locate the pole, P, we can draw a line parallel to MN through P as shown by M’N’ in Fig.
1.2b. The line M’N’ intersects the circle at N’ and the coordinates of N’, (σ θ τ θ , ) represent
the normal and shear stresses on MN.
EXAMPLE 1.1
A sample of soil 100 mm 100 mm is subjected to the forces shown in Fig. E1.1a.
Determine (a) 1 3 σ ,σ and ψ ; (b) the maximum shear stress, and (c) the stresses on a
plane oriented at 300
clockwise to the major principal stress plane.
Figure E1.1a
Strategy. There are two approaches to solve this problem. You can either use Mohr’s
circle or the appropriate equations. Both approaches will be used here.
1.4 Mohr-Coulomb Failure Criteria
Coulomb (1776) suggested that the shear strength of a soil along a failure plane
could be described by:
τ f = c +σ n tanφ (1.9)
where τ f is the shear strength on the failure plane, σ n is the stress normal to the
plane, c is the cohesion and φ the angle of internal friction of the soil. The two
parameters c and φ are called shear strength parameters.
To understand the concept behind Eq. (1.9), consider two blocks A and B (Fig
[Show More]